High Head Agricultural 4290, 4291

Specifically designed for lagoon or sump pit applications

  • Passes 1 1/2″ spherical solids
  • Available with 2″ or 3″ NPT vertical flange discharge
  • Durable cast iron construction with stainless steel screws and handle
  • Corrosion resistant powder coated epoxy finish
  • Oil-filled, hermetically sealed, thermal overload protection with automatic reset
  • Maximum operating temperature 130° F (54°C)
  • Shaft seals – silicon carbide/silicon carbide lower and carbon/silicon carbide upper seals
  • Neoprene gaskets and seals
  • Double shaft seals provides extra protection for motor
  • Large clearances to prevent stoppage from build up of solids
  • Pump flotation devices available for lagoon installations (See FM1473)
  • Width: 12 7/8″
  • Height: 20 1/2″

Pump Pontoons (See FM1507 for specs):
P/N 10-0624 Pontoon and hardware kit for connection to 2″ discharge conduit
P/N 10-0625 Pontoon and hardware kit for connection to 3″ discharge conduit

Pipe Floats:
P/N 10-0631 Includes four floats with nylon pipe straps

Standard Models – 50 ft. Power Cable – No molded plug.

Horsepower:  1 HP (4290) or 2 HP (4291)
Volts:  230 V
Hertz:  60 Hz
Phase:  Single or 3 Phase
Thermally protected:  Yes.
RPM:  3450 RPM
Impeller Type: Non-clogging vortex impeller
Cord Length: 50 ft (extra lengths 75-100 ft available)
Cord Type: UL listed neoprene jacketed power cable

To purchase Zoeller pumps, accessories and water treatment equipment go to our online store, to get a custom quote via email; info@water-services.usor use the online form, or call +1-801-225-1180.

Posted in pumps, Specialty Products, Submersible Pumps, Water Services Inc, Zoeller | Tagged , , , , | Leave a comment

Evaporative Cooling Pump Models 371, 372, 373

Continuous duty submersible pumps for dewatering or effluent evaporative cooling pumps for poultry applications.

  • Cast iron motor & pump housing with corrosion resistant powder coated epoxy finish
  • Motor – 60 Hz, oil-filled, hermetically sealed, automatic reset thermal overload protected
  • Permanently lubricated upper and lower bearings
  • Stainless steel screws and handle
  • No sheet metal parts to rust or corrode
  • No screens to clog
  • Glass-filled, engineered plastic non-clogging vortex impeller with metal insert
  • Watertight neoprene square ring between motor and pump housing
  • Silicon Carbide/Carbon shaft seal
  • Entire unit pressure tested after assembly
  • Maximum temperature for effluent or dewatering—130°F (54°C)
  • 1½” NPT Discharge
  • Completely submersible
  • Watertight and dust tight
  • Models available:
    • 371 – .3 HP, 115 V or 230 V, 1 Ph
    • 372 – 1/3 HP, 115 V or 230 V, 1 Ph
    • 373 – .4 HP, 115 V or 230 V, 1 Ph
Horsepower:  .3, 1/3, .4 HP
Volts:  115 or 230 V
Hertz:  60 Hz
Phase:  Single Phase
Thermally protected:  Yes
Impeller Type: Glass-filled, engineered plastic non-clogging vortex with metal insert
Cord Length: 20 ft.
Cord Type: UL listed power cord with molded 3-wire plug

Models 371, 372, 373

To purchase Zoeller pumps, accessories and water treatment equipment go to our online store, to get a custom quote via email; info@water-services.usor use the online form, or call +1-801-225-1180.

 


Posted in EVAPORATIVE COOLING, pumps, Specialty Products, Water Services Inc, Zoeller | Tagged , , , | Leave a comment

Drain Pump With Special Options 105-0010, 135-0005

Zoeller Specialty Products

2″ inlet drain pump (105-0010) and high head drain pump (135-0005). Removes water from areas where gravity flow is unavailable.

Applications include laundry tray pump, wet bar sink, lavatory, air conditioning condensate or dehumidifier water removal. Can also be used in conjunction with dishwashers and garbage disposal applications.
No inlet filters or screens to clean.

Drain Pump Series Includes:

  • Automatic pumps with tank cord seals and all hardware for easy assembly
  • Polypropylene basin and lid
  • Internal discharge pipe to lid
  • Check valve (model 105: 30-0181, Model 135: 30-0102)

Pump Features
105-0010 (Model 53)

  • 2″ inlet
  • Passes laundry lint
  • Automatic, float operated mechanical switch
  • 115 V/1 Ph, 60 Hz
  • 1550 RPM
  • 9 ft. UL listed 3-wire cord and plug
  • Stainless steel screws, guard, handle and switch arm
  • Passes 1/2″ spherical solids
  • 1 1/2″ NPT discharge
  • Non-clogging vortex impeller
  • Glass-filled polypropylene base with built in strainer
  • Temperature rated 130°F (54°C)
  • UL listed pump
  • Shipping weight: 30 lbs

Pump Features
135-0005 (Model 152)

  • High head
  • Passes laundry lint
  • Durable cast iron construction
  • Corrosion resistant powder coated epoxy finish
  • Stainless steel lifting handle
  • Assembled with stainless steel bolts
  • Non-clogging engineered thermoplastic vortex impeller design
  • Passes 3/4″ spherical solids
  • Temperature rated 130°F (54°C)
  • Motor: 60 Hz, 3450 RPM, oil-filled, hermetically sealed, automatic reset thermal overload protected
  • Carbon/ceramic seals
  • Upper sleeve bearing and lower ball bearing running in bath of oil
  • .4 HP
  • 15 ft. UL listed power cord with molded 3-wire plug and wired-in vertical float switch
  • 1 1/2″ NPT discharge
  • cCSAus certified pump
  • Shipping weight: 48 lbs

Basin:

  • Polyethylene construction
  • Corrosion resistant
  • High capacity
  • Gasketed polyethylene lid
  • 2″ NPT vent
  • 1 1/2″ NPT discharge
  • 2″ NPT inlet – no screen
  • Threaded connections for easy installation
  • Height: 15 1/2″
  • Width: 15 3/4″
  • Weight: 5 lbs
  • Gas tight cover
  • Temperature rated 130°F
  • Fits under single or double laundry tray sinks

Check Valve (30-0181)

  • ‘Full Flow’ design
  • 1 1/2″ or 1 1/4″ slip x slip union
  • PVC constructions

For additional specifications see FM0217

Check Valve (30-0102)

  • ‘Full Flow’ design
  • 1 1/2″ solvent weld
  • PVC construction

 

 

 

 

 

 

 

 

 

 

 

 

 

Posted in pumps, Specialty Products, Water Services Inc, Zoeller | Tagged , , , | 2 Comments

Drain Pump Series 104, 105, 110, 115, 120, 131, 132

Zoeller Specialty Pumps

Removes water from areas where gravity flow is not available.

  • Applications include laundry tray pump, wet bar sink, lavatory, air conditioning condensate and dehumidifier water removal. Can also be used in conjunction with dishwashers and garbage disposal applications.
  • No inlet filters or screens to clean
  • Optional top or side inlet
  • Can be installed with internal trap
  • Automatic pumps with tank cord seals
  • All hardware for easy assembly
  • Polypropylene basin and lid
  • Internal discharge pipe to lid (trap supplied by others)
  • Check valve (30-0181, not included with model 104)
  • Contact factory for additional inlet option or high head applications
  • Easy installation, no need to dig a sump
  • 132 comes preassembled

 

Drain pump Series

Model Pump with Basin

104*

M72

105

M53

110

M55

115

M57

120

M59

131

M98

132*

M72

 

Pump features (models 53, 55, 57, 59, 98):

  • Passes laundry lint
  • Automatic, float operated mechanical switch
  • 115V/1 Ph, all drain pump series
  • 9 ft. UL listed 3-wire cord and plug (15 ft. cord standard on model 98)
  • Stainless steel screws, guard, handle and switch arm
  • Passes ½” spherical solids
  • 1 ½” NPT discharge
  • 1550 RPM, 60 Hz on 50 series models
  • 1725 RPM on model 98
  • Non-clogging vortex impeller
  • Glass-filled, polypropylene base with built in strainer on M53 and M55.
  • Model 59, all bronze construction
  • Models 57 and 98 all cast iron construction
  • Temperature rated 130°F
  • UL Listed pump

Model 72:

  • Passes laundry lint
  • 115V/1 PH, all drain pump series
  • 9 ft. UL listed 3-wire cord and plug
  • Stainless steel screws, switch arm and lower motor housing
  • Oil free
  • Passes 3/8” spherical solids
  • 1 ½” NPT discharge
  • 3400 RPM
  • Non-clogging vortex impeller
  • Temperature rated 110°F
  • cCSAus certified pump

Basin:

  • Polypropylene construction
  • Corrosion resistant
  • High capacity
  • Gasket sealed polypropylene lid
  • 2” NPT vent
  • 1 ½” NPT discharge
  • 1 ½” compression slip fit for top and side intake Note: 132 comes preassembled, for side inlet only
  • Threaded connections for easy installation
  • May be installed with internal trap for space savings
  • Gas tight cover
  • Temperature rated 130°F
  • Fits under most sinks
  • Basin passes 10’stack test – Models 104 and 132 will not pass 10’ stack test

Check valve (excluding model 104)(30-0181)

Posted in pumps, Specialty Products, Water Services Inc, Zoeller | Tagged , , , | Leave a comment

Condensate 521; Zoeller Specialty Products

Multi-purpose Condensate pump.

  • Automatically removes condensation from air conditioning and 90+ condensing furnaces as well as dehumidifiers, ice makers, water coolers and refrigeration systems
  • Indicator lights for power (green), pump run (yellow) and high level alarm (red)
  • 3/8″ ID discharge with check valve
  • Handles condensate up to 140° F (60° C)
  • 20 ft TDH
  • Compact design (6″ x 6″ x 11-1/2″ long)
  • 1 gallon capacity
  • Built-in safety switch
    • Will automatically shut pump down in event of failure
    • Has 1/4″ quick connects for safety switch and alarm
  • 115 Volt AC, 1 phase
  • 6′ power cord
  • Listed in US and Canada
  • 24 month limited warranty
  • 4 inlet options

Volts:  115 Volts AC

Phase:  Single Phase

Cord Length: 6 ft

To purchase Zoeller pumps, accessories and water treatment equipment go to our online store, to get a custom quote via email; info@water-services.usor use the online form, or call + 1-801-225-1180.


Posted in condensate, multi-purpose, Specialty Products, Water Services Inc, Zoeller | Tagged , , , , | Leave a comment

Basement Sentry® Series 507, 510; Zoeller Specialty Products

Features & Benefits

12 Volt DC backup sump pump systems

Application- for clear water, emergency backup usage when power is off or the primary pump(s) fail

Extra protection when the primary AC pump fails due to power outages in storms, brownouts, wiring or electrical problems, when the primary pump fails due to damage, mechanical malfunction or obstructions in the pit, or when the primary pump fails to keep up with excessive water due to rain or overloading

No other system offers the reliability and protection provided by the Basement Sentry® Series.

Model 510 provides high capacity protection and recovery capabilities for dewatering in critical installations including residential locations, commercial locations, basement storage facilities, communication vaults or computer vaults (see performance data)

Zoeller’s time tested design experience gives you the needed performance and reliability

Pumps:

  • 12 volt, highly efficient with noncorrosive pump construction (supplied with 6’ leads)
  • Control Boxes:
  • All models have battery burn out and overcharge protection
  • Model 507 and 510 have a self-contained 10 amp battery recharger
  • All systems are fully solid state automatic controllers with alarms, light indicators and have warning systems
  • Light Indicators:
  • Long lasting LED light indicating power supply ‘on’
  • Battery partially charged
  • Pump alarm ‘off’
  • Run light and battery fully charged
  • Alarms:
  • Continuous steady beep – ‘low battery’
  • Slow interrupted beep – ‘partially discharged battery’ (for the Model 510 only)

Control Device: Reliable low voltage float switch

Battery Case:

  • The included battery case will accommodate maximum battery dimensions of 13”(L) x 7 ½”(W) x 9 ½”(H) and fits all group size 27 marine batteries
  • Made from noncorrosive polyethylene
  • Contains lock strap
  • Model 510 can be used with multiple batteries
  • Order extra battery case with hookup wire (P/N 007861)

Fittings:

Furnished with all required fittings

Model 507  has internal check valve in the discharge and includes an additional heavy-duty check valve adaptable to 1 ¼” or 1 ½” pipe

Model 510 includes two heavy-duty check valves to install with pedestal/column or submersible pumps

Sump pump not included

Warranty:

12 months from date of installation or 18 months from date of manufacture. However the 12 month warranty is extended to 36 months with the purchase of an Aquanot® battery by Zoeller. Note: Three year limited warranty valid only when a complete system is purchased and used as a backup to a primary dewatering system. A complete system includes a Model 507 or 510 Basement Sentry™ and an Aquanot® battery. To validate the warranty, the warranty card (FM1679), included with a Basement Sentry™ pump, must be filled out and returned to factory

Battery Life:

The estimated life of a fully charged (175 minute reserve capacity) battery when the pump is operating continuously is approximately 7 ½ hours. Example – The model 510 at 10 ft. head will pump 1,296 GPH. Most backup systems require intermittent pump operation. All models will provide protection for extended periods of time dependent upon stop-start requirements. Note: The 510 offers extended backup protection if the regular primary sump pump fails.

Performance Data:

Pump performance is based on the use of a fully charged 12 Volt, (200 minute reserve capacity) for models 507 and 510, deep-cycle battery with no deficiency and less than two years old.

Aquanot® Battery:

Size 31 “Wet” P/N 10-0761 (69 lbs.), shipped via truckline only, 200 minute reserve capacity

Size 27 “AGM” P/N 10-1450 (66 lbs.), 175 minute reserve capacity

Minimum battery requirements: deep cycle, size 27, 175 minute reserve capacity

See FM1311 (Model 507), or FM1139 (Model 510) installation instructions.

To purchase Zoeller pumps, accessories and water treatment equipment go to our online store, to get a custom quote via email; info@water-services.usor use the online form, or call + 1-801-225-1180.
Posted in Back Up, Battery, pumps, Specialty Products, Submersible Pumps, Water Services Inc, Zoeller | Tagged , , , , , | Leave a comment

Aquanot® Series 580, 585; Zoeller Specialty Products

Battery backup pedestal sump pump

  • Extra protection when your primary pump fails for any reason
  • No interruption in pump performance because of power outage or failure of primary pump
  • One of the most reliable and well-established battery backup systems in use today
  • 25 years of proven performance in the field and thousands of satisfied customers
  • Pump has heavy duty 12 Volt motor and positive contact float switch
  • Stainless steel column and shaft
  • Noncorrosive base assembly
  • Discharges water as fast as many 1/3 HP primary pumps
  • Aquanot® I equipped with .5 amp battery monitor designed to maintain a fully charged battery
  • Aquanot® II equipped with automatic electronic 28 amp charger to maintain and recharge battery
  • Pump alarm included with all Aquanot® pumps
  • *Warranty: 12 months from date of installation or 18 months from date of manufacture. However, the 12 month warranty is extended to 36 months with the purchase of an Aquanot® battery by Zoeller.
  • Model 580 (Aquanot® I) comes with battery monitor
  • Model 585 (Aquanot® II) comes with electronic charger
  • Minimum pit requirements 18″ x 22″

For AC pump backup & emergency use.

The complete Aquanot® I system includes the pump, the battery monitor and a 12V pump alarm. You may purchase the DEEP-CYCLE battery and battery box separately.

The Complete Aquanot® II system includes the pump, the electronic charger and a 12V pump alarm. You may purchase the DEEP-CYCLE battery and battery box separately.

Battery Monitor:

Aquanot® I is designed to maintain a standing battery at full charge by trickling ½ amp. It will not recharge a spent battery after a long power outage. A conventional battery charger must be used to recharge the battery. The battery monitor will once again maintain a battery charge until your pump is needed again.

Aquanot® II comes with these electronic charger features:

  • 28 amp battery charger
  • LED status indicators
  • Automatic battery recharging
  • Microprocessor controlled
  • Each unit individually tested
  • 3.5 amp AC input
  • 12V DC output
  • Because this unit converts AC to DC, this pump will operate for an extended time as a backup unit in case of primary pump failure

Aquanot® Battery:

  • Size 31 “Wet” No. 10-0761 (69 lbs), 200 minute reserve capacity
  • Size 27 “AGM” No. 10-1450 (66 lbs), 175 minute reserve capacity
  • Minimum battery requirements deep cycle, size 27, 175 minute reserve capacity

See FM1613 for Model 580 and 585 installation instructions.

Volts:  12 Volt motor

Posted in Back Up, Battery, pedestal, pumps, Specialty Products, Submersible Pumps | Tagged , , , , | Leave a comment

Aeration/Fountain Pump 370-0002; Zoeller Specialty Products

Produces water fountain up to 15 feet in height.

  • Produces water fountain up to 15 ft. in height
  • Easy to install – preassembled with Water Lily pattern
  • Operates in 5 ft. of water or more
  • Aerates up to 4,900 gallons of water per hour
  • Continuous duty
  • 6″ circulator screen to draw water from below the surface for improved aeration and extended motor life
  • 100 ft. electrical cable with GFCI plug connects directly to 120V outlet.
  • Flotation system with UV resistant polyethylene float
  • Eye bolts for anchoring
  • 12 month limited warranty
  • Adds unique focal point and value to your home and property
  • Helps eliminate stagnant water
  • Reduces mosquitoes and algae build up
  • Water-cooled motor eliminates pollution risk and pond contamination
  • Applications include: waterscapes, pond aeration and golf courses

Three easily interchangeable patterns included:

  1. Water Lily – a symmetrical inverted bell shape (15′ @ 2,700 GPH)
  2. Sky Cannon – a dramatic single plume of water (15′ @ 3,300 GPH)
  3. Water Trumpet – an eye catching combination spray (15′ @ 4,900 GPH)

Horsepower:  1/2 HP

Volts:  115 V

Amp:  10.5 Amps

Cord Length: 100 ft.

Cord Type: Electrical cable with GFCI plug connects directly to 120 V outlet

To purchase Zoeller pumps, specialty products, accessories and water treatment equipment go to our online store, to get a custom quote via email; info@water-services.usor use the online form, or call + 1-801-225-1180.
Posted in Aeration, Fountain Pump, pumps, Specialty Products, Water Services Inc, Zoeller | Tagged , , , , | Leave a comment

High Temperature 3000 Series 3098, 3137, 3139, 3161, 3163, 3282; Zoeller Specialty Products

Submersible pumps for use in dewatering applications up to 200° F. 

  • A high temperature submersible pump series with electrical components meeting the National Electrical Code requirements for 200° F service
  • Comprehensive line of models, styles and modes
  • Conduit length is 3 feet for automatic models and 6 feet for nonautomatic models
  • Power cord length is 15 feet for automatic models and supplied by others for nonautomatic models
  • High temperature liquid-tight conduit used with high temperature cable
  • High temperature motor windings
  • High temperature Viton® gaskets
  • High temperature thermal overload protected
  • All control components in contact with water are high temperature rated
  • All models have stainless steel screws, guards, handles and control arm and seal assemblies
  • Float operated mechanical switch box which is mounted on the discharge pipe above the operating level (switch box is not intended to come in continuous contact with 200° F water)
  • Mechanical seal has NI-Resist rotary face and Viton® elastomer
  • Corrosion resistant powder coated epoxy finish

Horsepower:  1/2 HP

Volts:  115 or 230 V

Phase:  Single Phase

Impeller Type: Vortex impeller

Cord Length: 15 ft.

To purchase Zoeller pumps, specialty products, accessories and water treatment equipment go to our online store, to get a custom quote via email; info@water-services.usor use the online form, or call + 1-801-225-1180.
Posted in Dewatering, pumps, Specialty Products, Submersible Pumps, Water Services Inc, Zoeller | Tagged , , , , | Leave a comment

2000 Series High Temp 2057, 2098, 2137, 2282; Zoeller Specialty Products

Submersible pumps for use in dewatering applications. Intermittent use up to 200° F.

  • All models are designed to meet specifications with assurance by using high temperature parts rated for intermittent 200° F contact
  • High temperature switch components rated for intermittent service up to 200° F
  • Available in a variety of styles and performances
  • All models built to last
  • High temperature motor leads and thermal overload protection
  • 100% corrosion resistant powder coated epoxy finish
  • 10 ft cord, high temperature, adjustable float operated mechanical switch mounts directly to the discharge pipe (BN & BE models)
  • 1 1/2″, 2″ or 3″ discharge
  • Adjustable float switch is not intended for continuous contact with 200° F water
  • All stainless steel fittings
  • 100% factory tested and approved

Typical Installations:

  • Boiler blow down
  • Hot water transfer
  • Plant wash down
  • Transformer vaults
  • Industrial steam cleaning

Switch Data:

  • 16 guage 2 conductor SOOW switch cordage
  • Float housing constructed of high impact ABS
  • 13 Amps (max) steady state
  • Intermittent direct contact with up to 200° F water
  • Turbulence resistant float switch
  • Adjustable pumping range (see chart)
  • Unlimited repetitive exposures are permissible for applications below 180° F

Horsepower:  .3 – 1/2 HP

Volts:  115 or 230 V

Hertz:  60 Hz

Phase:  Single Phase

Impeller Type: Non-clogging vortex impeller

Cord Length: 15 ft

Cord Type: High temperature 16 guage heavy duty SOOW cord

Available in the following Models

To purchase Zoeller pumps, specialty products, accessories and water treatment equipment go to our online store, to get a custom quote via email; info@water-services.usor use the online form, or call + 1-801-225-1180      .

Posted in Specialty Products, Submersible Pumps, Water Services Inc, Zoeller | Tagged , , , | Leave a comment